РУБ.

TWI

В. С. Прокопенко Программирование микроконтроллеров ATMEL на языке C (+ CD-ROM)

В. С. Прокопенко Программирование микроконтроллеров ATMEL на языке C (+ CD-ROM)

Бренд:

Эта книга - сборник примеров программ на языке . С для микроконтроллеров производства . ATMEL. . В качестве средств разработки и имитации использованы компилятор . Win. AVR, среда . AVR . Studio и имитатор схем . Proteus . ISIS. . Синтаксические особенное языка . С и методы работы с перечисленными выше инструментальными средствами в книге подробно не рассматриваются, поскольку автор преследовал цель дать максимальное число практических примеров использования тех или иных периферийных устройств микроконтроллера: таймеров/счетчиков, приемопередатчика . U(S). ART, аналогового компаратора, . АЦП, интерфейсов . SPI и . TWI, памяти . Flash и . EEPROM. . Отдельная глава посвящена взаимодействию с . ЖК-модулем. . Таким образом, это издание рассчитано на тех читателе которые, обладая базовыми познаниями языка . С, желают научиться применять их в работе с микроконтроллерами . ATMEL.

749.00 Р.

LCD1602 Screen Module Display w/ IIC / SPI Expansion Board

LCD1602 Screen Module Display w/ IIC / SPI Expansion Board

Бренд: DX

Model . No . Quantity 1 . Color . Green + red . Material . PCB board . Specification 2. 6 . LCD display; . Input voltage: . DC 5. V; 1 . LAT: 74. HC595 data storage terminal; 2 . DAT: . I2. C / . TWI / . IIC . SDA 74. HC595 data terminal; 3 . CLK: . I2. C / . TWI / . IIC . SCL 74. HC595 pulse terminal; 4 +5. V: 5. V input; 5 . GND: . Power supply negative pole . Features . Transfer serial data to parallel data via . I2. C / . TWI / . IIC bus or . SPI bus and send to . LCD1602 to control it; . Control . LCD1602 with 4 . I2. C or 5 . SPI cables; . Allows to adjust contrast via onboard potentiometer . Application . For . DIY project . Packing . List 1 x . LCD1602 1 x . Expansion adapter board

786.08 Р.

Mega IO Sensor Expansion Shield / Board For Arduino V1.2(Works with Official Boards)

Mega IO Sensor Expansion Shield / Board For Arduino V1.2(Works with Official Boards)

Бренд: DX

Color: . Black - . Extends 54 digital . I/. O pins and power - . Extends 16 analog . I/. O pins and power - . Support . Xbee / . Bluetooth . Bee - . Support 3. 3. V output - . Support . SD module - . Support . IIC/. I2. C/. TWI

742.63 Р.706.04 Р.

IIC/I2C/TWI SPI Serial LCD 1602 Module Electronic building block for Arduino

IIC/I2C/TWI SPI Serial LCD 1602 Module Electronic building block for Arduino

Бренд: DX

Model . IIC_. LCD02 . Quantity 1 . Color . Blue . Material . PCB . Features 2. 6 . LCD display supports . IIC / . SPI . Application . DIY . Arduino based project . Packing . List 1 x . Arduino electronic building block

768.36 Р.

IIC / I2C TWI SPI Serial LCD 1602 Module  for Arduino (Works with Official Boards)

IIC / I2C TWI SPI Serial LCD 1602 Module for Arduino (Works with Official Boards)

Бренд: DX

Model . IIC_. LCD02 . Quantity 1 . Color . Blue + . Green . Material . FR-4 . Features 2. 7 . LCD display with . IIC & . SPI interfaces . Application . Great for . DIY project . Packing . List 1 x . Arduino . IIC / . I2. C / . TWI . SPI serial . LCD 1602 module

799.80 Р.

FreArduino ADK Main Board Module for Arduino (Works with Official Boards)

FreArduino ADK Main Board Module for Arduino (Works with Official Boards)

Бренд: DX

Model . ADK02 . Quantity 1 . Color . Red . Material . FR4 . Features . Compatible with . Google . ADK / . Arduino . Mage . ADK; 56 digital . IOs; 16 analog input; 14 . PWM outputs; 4 hardware serial ports; 1 hardware . TWI; 1 hardware . SPI (up to 8. Mbps); . Working voltage: 3. 3. V / 5. V (selectable) . Application . Arduino . DIY project . Packing . List 1 x . Main board 1 x . Mini . USB cable (22cm)

4327.72 Р.2591.49 Р.

FR4 Bluetooth Sensor Expansion Board Module - Red + Blue Black

FR4 Bluetooth Sensor Expansion Board Module - Red + Blue Black

Бренд: DX

Great for people loving making electronics; 14-. IO ports (12 servo ports) and power port; 6-analog . IO port; . One digital port; . Can be shifted between digital external power port and on-board power; . With one external power input socket and one input pin; . RS485 port (D0-. RX . D1-. TX . D2-. EN); . With reset button; xbee / . Bluetooth . Bee bluetooth wireless data port; . APC220 / . Bluetooh . V3 port; . IIC / . I2. C / . TWI output port; 3. 3. V ouput port; . SD card module port. . A product for . Arduino that works with official . Arduino boards.

655.73 Р.560.26 Р.

Meeeno IIC LCD-1602 Blue Screen LCD Module Shield for Arduino

Meeeno IIC LCD-1602 Blue Screen LCD Module Shield for Arduino

Бренд: DX

Brand . Meeeno . Model . IIC . LCD-1602 blue screen shield . Quantity 1 . Color . Orange + blue . Material . FR4 . Features . It is a simple version of . Arduino . IIC / . TWI / . SPI . LCD . With most function of them and communicate through . IIC only takes two . IO port; . But deletes . SPI port convenient and easy to use . Specification . Working voltage: 5. V; . Mode of connection: . GND-. GND . VCC-. VCC . SDA-. A4 . SCK-. A5; 2. 6 display screen . Application . Great for . DIY project . English . Manual/. Spec . Yes . Packing . List 1 x . Expansion board

588.84 Р.

MaiTech 03100623 ATMEGA48 + NRF24L01 Interface Wireless Development Board Module - Black

MaiTech 03100623 ATMEGA48 + NRF24L01 Interface Wireless Development Board Module - Black

Бренд: DX

Adopts . I2. C (TWI) communication protocol which greatly simplifies the communication process of . NRF24. L01and improves the efficiency of project development; . Each module is as . I2. C (TWI) slave (address 35); . Smooth two-way communication regardless of the slave and master; . Maximum transmission distance can reach 70m (only for production test); . Wireless communications chip . NRF24. L01 reliable communication protocol reducing data loss; . I2. C/. TWI protocol greatly simplifies the communication lines; . Perfectly compatible with arduino; . Applications: . Robot control remote control and . Information collection etc. ; . Note: . The wireless communications may have radiation not recommended for use in life protection

339.59 Р.

IIC/I2C/TWI SPI Serial 2.6 LCD 1604 Module Electronic Building Block for Arduino

IIC/I2C/TWI SPI Serial 2.6 LCD 1604 Module Electronic Building Block for Arduino

Бренд: DX

Model . N/. A . Quantity 1 . Color . Green . Material . FR4 . Features 2. 6 . LCD display supports . IIC / . SPI . Application . DIY . Arduino based project . Packing . List 1 x . Arduino electronic building block

1336.05 Р.1285.17 Р.

MB_Due Singlechip Development Board - White + Black (7~23V)

MB_Due Singlechip Development Board - White + Black (7~23V)

Бренд: DX

Model: . MB_. Due - . Quantity: 1 - . Color: . White + black - . Material: . Semi-soft fiber . FR4 - . Microcontroller: . Atmel . SAM3. X8. E - . Operating . Voltage: 3. 3. V - . Recommended . Input . Voltage: 7~23. V - . Digital . I/. O . Pins: 54 (of which 12 provide . PWM output) - . Analog . Input . Pins: 12 - . Analog . Outputs . Pins: 2 - . Total . DC . Output . Current on all . I/. O lines: 130m. A - . DC . Current for 3. 3. V . Pin: 800m. A - . DC . Current for 5. V . Pin: 2. A - . The . Due is . Arduinos first . ARM-based . Arduino development board. . This board is based on a powerful 32bit . Cortex. M3 . ARM microcontroller made programmable through the familiar . Arduino . IDE. . It increases the computing power available to . Arduino users keeping the language as compatible as possible so that many programs will be migrated in a matter of minutes; the . DC input current from . Max 800m. A to . Max 2. A and input voltage from 7~20. V to 7~23. V. - . The . Arduino . Due has 54 digital input / output pins (of which 12 can be used as . PWM outputs) 12 analog inputs 4 . UARTs (hardware serial ports) an 84 . MHz clock a . USB-. OTG capable connection 2 . DAC (digital to analog) 2 . TWI a power jack an . SPI header a . JTAG header a reset button and an erase button. . There are also some cool features like . DACs . Audio . DMA an experimental multi tasking library and more - . Note: . Unlike other . Arduino boards the . Arduino . Due board runs at 3. 3. V. . The maximum voltage that the . I/. O pins can tolerate is 3. 3. V. . Providing higher voltages like 5. V to an . I/. O pin could damage the board - . Packing . List: - 1 x . Development board

2797.87 Р.

IIC/I2C/TWI SPI Serial 3.3 LCD 2002 Module Electronic Building Block

IIC/I2C/TWI SPI Serial 3.3 LCD 2002 Module Electronic Building Block

Бренд: DX

Model . N/. A . Quantity 1 . Color . Green . Material . FR4 . Features 3. 3 . LCD display supports . IIC / . SPI . Application . DIY . Arduino based project . Packing . List 1 x . Electronic building block

1257.73 Р.1186.84 Р.

Lteaduino Leonardo ATMEGA32U4 Learning Microcontroller Development Board (Official Improved Version)

Lteaduino Leonardo ATMEGA32U4 Learning Microcontroller Development Board (Official Improved Version)

Бренд: DX

Overview . The . Iteaduino . Leonardo is a microcontroller board based on the . ATmega32u4 it's 100% compatible with . Arduino . Leonardo. . It has 20 digital input/output pins a 16 . MHz crystal oscillator a micro . USB connection a power jack an . ICSP header and a reset button. . It contains everything needed to support the microcontroller; simply connect it to a computer with a . USB cable or power it with an . AC-to-. DC adapter or battery to get started. . The . Iteaduino . Leonardo differs from all preceding boards in that the . ATmega32u4 has built-in . USB communication eliminating the need for a secondary processor. . This allows the . Leonardo to appear to a connected computer as a mouse and keyboard in addition to a virtual (CDC) serial / . COM port. . It also has other implications for the behavior of the board. . Features . Efficient . DC-. DC . Power supply with wide range input 3. 3. V/5. V . Operating . Voltage selection . All pins out for . Sensor and . Servo . UART/. IIC interface breakout . Power . Supply . The . Arduino . Leonardo can be powered via the micro . USB connection or with an external power supply. . The power source is selected automatically. . External (non-. USB) power can come either from an . AC-to-. DC adapter (wall-wart) or battery. . The adapter can be connected by plugging a 2. 1mm center-positive plug into the board's power jack. . Leads from a battery can be inserted in the . Gnd and . Vin pin headers of the . POWER connector. . The board can operate on an external supply of 7 to 23 volts. . If supplied with less than 7. V however the 5. V pin may supply less than five volts and the board may be unstable. . The power pins are as follows: . VIN. . The input voltage to the . Iteaduino board when it's using an external power source (as opposed to 5 volts from the . USB connection or other regulated power source). . You can supply voltage through this pin or if supplying voltage via the power jack access it through this pin. 5. V. . The regulated power supply used to power the microcontroller and other components on the board. . This can come either from . VIN via an on-board regulator or be supplied by . USB or another regulated 5. V supply. 3. V3. . A 3. 3 volt supply generated by the on-board regulator. . Maximum current draw is 250 m. A. . GND. . Ground pins. . IOREF. . The voltage at which the i/o pins of the board are operating ( . VCC for the board). . This is 5. V on the . Iteaduino . Leonardo. . Input and . Output . Each of the 20 digital i/o pins on the . Uno can be used as an input or output using pin . Mode digital . Write and digital . Read functions. . They operate at 5 volts. . Each pin can provide or receive a maximum of 40 m. A and has an internal pull-up resistor (disconnected by default) of 20-50 k. Ohms. . In addition some pins have specialized functions: . Serial: 0 (RX) and 1 (TX). . Used to receive (RX) and transmit (TX) . TTL serial data using the . ATmega32. U4 hardware serial capability. . Note that on the . Leonardo the . Serial class refers to . USB (CDC) communication; for . TTL serial on pins 0 and 1 use the . Serial 1 class. . TWI: 2 (SDA) and 3 (SCL). . Support . TWI communication using the . Wire library. . External . Interrupts: 2 and 3. . These pins can be configured to trigger an interrupt on a low value a rising or falling edge or a change in value. . See the attach . Interrupt function for details. . PWM: 3 5 6 9 10 11 and 13. . Provide 8-bit . PWM output with the analog . Write function. . SPI: on the . ICSP header. . These pins support . SPI communication using the . SPI library. . Note that the . SPI pins are not connected to any of the digital . I/. O pins as they are on the . Uno . They are only available on the . ICSP connector. . This means that if you have a shield that uses . SPI but does . NOT have a 6-pin . ICSP connector that connects to the . Leonardo's 6-pin . ICSP header the shield will not work. . LED13. . There is a built-in . LED connected to digital pin 13. . When the pin is . HIGH value the . LED is on when the pin is . LOW it's off. . Analog . Inputs: . A0-. A5 . A6 - . A11 (on digital pins 4 6 8 9 10 and 12). . The . Leonardo has 12 analog inputs labeled . A0 through . A11 all of which can also be used as digital i/o. . Pins . A0-. A5 appear in the same locations as on the . Uno; inputs . A6-. A11 are on digital i/o pins 4 6 8 9 10 and 12 respectively. . Each analog input provides 10 bits of resolution ( 1024 different values). . By default the analog inputs measure from ground to 5 volts though is it possible to change the upper end of their range using the . AREF pin and the analog . Reference function. . There are a couple of other pins on the board: . AREF. . Reference voltage for the analog inputs. . Used with analog . Reference. . Reset. . Bring this line . LOW to reset the microcontroller. . Typically used to add a reset butto

1218.85 Р.

Arduino Compatible DUE R3 32 Bit ARM With USB Cable

Arduino Compatible DUE R3 32 Bit ARM With USB Cable

Бренд: Arduino

Arduino . Compatible . DUE . R3 32 . Bit . ARM . With . USB . Cable . Compatible . All . Arduino . Shield . Description: . The . Arduino . Due is a microcontroller board based on the . Atmel . SAM3. X8. E . ARM . Cortex-. M3 . CPU (datasheet). . It is the first . Arduino board based on a 32-bit . ARM core microcontroller. . It has 54 digital input / output pins (of which 12 can be used as . PWM outputs) 12 analog inputs, 4 . UARTs (hardware serial ports) a 84 . MHz clock, an . USB . OTG capable connection, 2 . DAC (digital to analog) 2 . TWI, a power jack, an . SPI header, a . JTAG header, a reset button and an erase button. . The board contains everything needed to support the microcontroller; simply connect it to a computer with a micro-. USB cable or power it with a . AC-to-. DC adapter or battery to get started. . The . Due is compatible with all . Arduino shields that work at 3. 3. V and are compliant with the 1. 0 . Arduino pinout. . The . SAM3. X has 512. KB (2 blocks of 256. KB) of flash memory for storing code. . The bootloader is preburned in factory from . Atmel and is stored in a dedicated . ROM memory. . The available . SRAM is 96. KB in two contiguous bank of 64. KB and 32. KB. . All the available memory (Flash, . RAM and . ROM) can be accessed directly as a flat addressing space. . It is possible to erase the . Flash memory of the . SAM3. X with the onboard erase button. . This will remove the currently loaded sketch from the . MCU. . To erase, press and hold the . Erase button for a few seconds while the board is powered. . Feature: . The . Arduino . Due has a 32-bit . ARM core that can outperform typical 8-bit microcontroller boards. . The most significant differences are: . A 32-bit core, that allows operations on 4 bytes wide data within a single . CPU clock. . CPU clock at 84. Mhz 96. KBytes of . SRAM 512. KBytes of flash memory for code . A . DMA controller, that can relieve the . CPU from doing memory intensive tasks . Warning: . Unlike other . Arduino boards, the . Arduino . Due board runs at 3. 3. V. . The maximum voltage that the . I / . O pins can tolerate is 3. 3. V. . Providing higher voltages, like 5. V to an . I / . O pin could damage the board. . Specification: . Microcontroller: . AT91. SAM3. X8. E . Operating voltage: 3. 3. V . Input voltage(recommended): 7. V - 12. V . Input voltage(limits): 6. V - 16. V . Digital . I / . O pins: 54(of which 12 provide . PWM output) . Analog input pins: 12 . Analog outputs pins: 2(DAC) . Total . DC output current on all . I / . O lines: 130m. A . DC current for 3. 3. V pin: 800m. A . DC current for 5. V pin: 800m. A . Flash memory: 512. KB all available for the user applications . SRAM: 96. KB(two banks: 64. KB and 32. KB) . Clock speed: 84. MHz . Package included: 1 x . Arduino compatible . DUE . R3 1 x . USB cable

14.09 Р.

Программирование микроконтроллеров ATMEL на языке C (+CD)

Программирование микроконтроллеров ATMEL на языке C (+CD)

Эта книга - сборник примеров программ на языке . С для микроконтроллеров производства . ATMEL. . В качестве средств разработки и имитации использованы компилятор . Win. AVR, среда . AVR . Studio и имитатор схем . Proteus . ISIS. . Синтаксические особенности языка . С и методы работы с перечисленными выше инструментальными средствами в книге подробно не рассматриваются, поскольку автор преследовал цель дать максимальное число практических примеров использования тех или иных периферийных устройств микроконтроллера: таймеров/счетчиков, приемопередатчика . U(S). ART, аналогового компаратора, . АЦП, интерфейсов . SPI и . TWI, памяти . Flash и . EEPROM. . Отдельная глава посвящена взаимодействию с . ЖК-модулем. . Таким образом, это издание рассчитано на тех читателей, которые, обладая базовыми познаниями языка . С, желают научиться применять их в работе с микроконтроллерами . ATMEL.

924.00 Р.

Киноальбом №11. Сборник о лучшей футбольной лиге (4DVD)

Киноальбом №11. Сборник о лучшей футбольной лиге (4DVD)

Вы держите в руках 263 минуты эксклюзивной серии фильмов об английском футболе: . Гол - вершина стараний футболистов. . Именно ради того, чтобы увидеть голы, болельщики ходят на футбол, берут на стадион своих детей, чтобы показать им этот сладкий миг взятия ворот. . . Данный фильм - своеобразная антология лучших мгновений . Премьер - лиги, отражающий ее историю со дня образования. . Английская . Премьер-лига - турнир, достойный наилучших эпитетов: самый яркий, самый захватывающий, самый богатый, самый зрелищный. . . Лучшие футболисты и тренеры мира приучили болельщиков к тому, что от каждой игры следует ожидать чего-то необычного и незабываемого. . Уникальное и захватывающее видео с участием лучших футболистов не даст . Вам расслабиться и хотя бы на секунду отвлечься от экранов телевизоров! . Так посмеемся же от души над курьезными голами, рукопашными схватками, обиженными судьями, эксцентричными болельщиками и расстроенными своей неуклюжестью игроками!!! . АНГЛИЙСКАЯ . ПРЕМЬЕР- . ЛИГА. . ЛУЧШИЕ . ГОЛЫ . ДЕСЯТИЛЕТИЯ - . Режиссер - . Стив . Пласто. . Продюсеры русской версии - . Михаил . Погосов, . Александр . Максимов. . Производство компаний . TWI в содружестве с . Английской . Премьер-лигой (FA . Premier . League), . Великобритания; длительность - 105 мин. , цветной, . PAL. . Спортивная программа. . Без ограничений по возрасту. . АНГЛИЙСКАЯ . ПРЕМЬЕР-. ЛИГА. . GOLDEN . MOMENTS. . Часть 1 - . Режиссеры - . Питер . Тоттал, . Тони . Харлей. . Продюсер русской версии . Михаил . Погосов. . Производство компании . TWI в содружестве с . Английской . Премьер-лигой (FA . Premier . League), . Великобритания. . Продолжительность - 53 мин. , цветной, . PAL. . Спортивная программа. . Без ограничений по возрасту. . АНГЛИЙСКАЯ . ПРЕМЬЕР-. ЛИГА. . GOLDEN . MOMENTS. . Часть 2 - . Режиссеры - . Питер . Топал, . Тони . Харлей. . Продюсер русской версии - . Михаил . Погосов. . Производство компании . TWI в содружестве с . Английской . Премьер-лигой (FA . Premier . League), . Великобритания. . Продолжительность - 53 мин. , цветной, . PAL. . Спортивная программа. . Без ограничений по возрасту. . АВТОГОЛЫ . И . ПРИКОЛЫ . АНГЛИЙСКОЙ . ПРЕМЬЕР-. ЛИГИ - . Режиссер дубляжа - . Алексей . Богачев. . Продюсеры русской версии - . Михаил . Погосов. . Александр . Максимов. . Производство компании . TWI, . Великобритания. . Продолжительность - 52 мин. , цветной, . PAL. . Развлекательная программа. . Без ограничений по возрасту.

633.00 Р.

TWI工作安全(JS)学员练习手册(日本产业训练协会TWI-MTP培训指定教材;新编21世纪精益

TWI工作安全(JS)学员练习手册(日本产业训练协会TWI-MTP培训指定教材;新编21世纪精益

Бренд: jd-книги

TWI工作安全(. JS)学员练习手册(日本产业训练协会. TWI-. MTP培训指定教材;新编21世纪精益

835.51 Р.

Модуль Board Порт IIC / I2C TWI SP ?? I Последовательный интерфейс для Arduino 1602 LCD

Модуль Board Порт IIC / I2C TWI SP ?? I Последовательный интерфейс для Arduino 1602 LCD

Бренд: youkeshu

Модуль . Board . Порт . IIC / . I2. C / . TWI / . SP ?? . I . Последовательный интерфейс для . Arduino 1602 . LCD

219.90 Р.